TECHNICAL DATA PST-01
PEEL STOP
®
TRIPLE THICK PRIMER
Form: GDH-311
Rev.: 030414
.DESCRIPTION AND USES .
Zinsser
®
Peel Stop
®
Triple Thick Primer is a water-based
acrylic binding primer designed to penetrate and stop
previous coatings from peeling. Peel Stop Triple Thick is
three times thicker than regular primers when applied
properly, so it fills and seals cracked, weathered, and
peeling surfaces, creating a smoother, more uniform
surface for finishing. It dries to a white finish to provide
contrast for application of finish coats. It has excellent
flexibility to allow for natural expansion and contraction on
wood and other exterior surfaces. Use on interior and
exterior surfaces such as previously painted wood, wood
siding, windows, baseboards, doors, fences, walls,
foundations, laminated wood, trim, PVC and plastic,
plywood, brick, stucco, masonry, concrete, plaster,
aluminum siding, metal gutters and downspouts,
galvanized steel, and fiberglass. Peel Stop Triple Thick
Primer can be top coated with any latex or alkyd paint.
PERFORMANCE CHARACTERISTICS .
• Stops peeling paint
• Creates a smooth finish
• Seals weathered surfaces
• Outstanding flexibility
• Dries white
• Fast dry – can be top coated in 2 hours
.PRODUCTS .
SKU Description
260925 1-Quart
260924 1-Gallon
260927 5-Gallon
PRODUCT APPLICATION .
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of dust, dirt,
excessive chalky material, grime, grease, oil, wax, mildew,
wallpaper, adhesive or any contamination that may
interfere with adhesion. Scrape loose and peeling paint
from the surface and wash with detergent or soap and
water. Sand any remaining paint film edges smooth. For
best results, pressure wash to remove exterior mold &
mildew with Zinsser JOMAX
®
Mildew Killer and House
Cleaner. Bare wood that has been exposed for more than
4 weeks should be lightly sanded to remove weathered
wood fibers. Allow the surface to dry completely before
applying Peel Stop Triple Thick Primer. Always test a
small area to ensure acceptable adhesion. To block stains
from water or bleeding woods, use a Zinsser stain
blocking primer such as Zinsser Cover Stain
®
. Spot prime
knots and severe stains with Zinsser B-I-N
®
Shellac base
Primer-Sealer before applying Peel Stop
®
Triple Thick
Primer.
PRODUCT APPLICATION (cont.) .
SURFACE PREPARATION (cont.)
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
APPLICATION
Apply only when air, material, and surface temperatures
are between 40-90ºF (4-32ºC) and the surface
temperature is at least 5ºF (3ºC) above the dew point. The
relative humidity should not be greater than 85%. Mix
thoroughly to ensure any settled pigment is re-dispersed
before using. Apply with brush and/or roller or airless
sprayer. Back brush or roll to work the product into cracks
and edges of old paint. Product may either be applied
lightly for basic priming and sealing, or follow with several
thick coats to bridge and fill cracked and uneven surfaces.
For severely peeled surfaces, apply a first coat thinned
with 10% water and work into the peeling paint. Apply the
product up to 30 mils wet per application, not to exceed 30
mils, which may result in mud cracking or sagging. For
best results when brushing, use high quality synthetic
bristle brushes. In most cases only one coat is necessary
to prime most surfaces. If excessive absorption occurs
over very porous substrates a second coat may be
necessary. For best results, prime entire surface before
painting. Keep container closed when not in use.
• Brush – Use synthetic (nylon, polyester or blend). Apply
a thick coat and work brush into peeling and cracked
areas.
• Roller – Recommend using a ½” nap roller. Roll product
on thick and work into peeling and cracked areas of the
surface. Apply additional coats as necessary.
• Airless Sprayer – Use 0.015” – 0.017” tip @ 2000-2500
psi.
Overlap previous pass by 1-2 inches.
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels