TECHNICAL DATA OLS-02
ODORLESS
PRIMER–SEALER STAIN BLOCKER
Form: GDH-370
Rev.: 052314
.DESCRIPTION AND USES .
Zinsser
®
Odorless aerosol is an easy to use, all-purpose,
low odor primer-sealer and stain blocker. It is designed for
interior applications where oil-base performance is
required but odor is a concern. It is suitable for sealing
nicotine, fire, smoke and water stains on surfaces such as
wood molding, trim and spackled areas. It adheres to
paneling, kitchen cabinets, glossy paints and hard-to-paint
objects, such as wicker, louvers, picture frames, and arts
and crafts. It is compatible with all latex and oil-based
architectural paints.
PERFORMANCE CHARACTERISTICS .
Blocks water, smoke and tannin stains
Bright white finish, non-yellowing formula
No lingering odor
Adheres to all surfaces
Recoat in 2 hours
.PRODUCTS .
SKU Container Size
3959 13 ounce spray
.PRODUCT APPLICATION .
SURFACE PREPARATION
Surfaces should be clean, dry, sound and free of dust, dirt,
grime, grease, oil, wax, mildew, wallpaper, adhesive or
any contamination that may interfere with adhesion. If
unsure of cleanliness, always wash surface with an
appropriate cleaning solution or solvent (do not use TSP
as a cleaner). Remove any peeling and/or unsound
coatings. Sand any remaining paint film edges smooth.
Allow surface to dry completely before priming. If
necessary, spot prime knots and sap streaks with B-I-N
®
Primer-Sealer before priming with Zinsser Odorless
Primer-Sealer Stain Blocker.
WARNING! If you scrape, sand or remove old paint, you
may release lead dust. LEAD IS TOXIC. EXPOSURE TO
LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS
BRAIN DAMAGE, ESPECIALLY IN CHILDREN.
PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH-Approved respirator to
control lead exposure. Clean up carefully with a HEPA
vacuum and a wet mop. Before you start, find out how to
protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead.
.PRODUCT APPLICATION (cont.)
APPLICATION
Apply only when air, material, and surface temperatures
are between 50-90ºF (10-32ºC) and relative humidity
should not be greater than 85%. Shake can vigorously
until the mixing ball begins to rattle. Turn upside down and
continue shaking for one minute. If mixing ball fails to rattle
DO NOT STRIKE CAN. Contact Rust-Oleum. Shake can
occasionally during use. Hold can upright 10-12" from the
object and spray in a steady back and forth motion with
short ‘dusting’ strokes, slightly overlapping each stroke.
Keep the can the same distance from the surface. Keep
the can in motion while spraying. To permanently block
heavy odors, use Zinsser B-I-N Ultimate Stain Blocker.
Do not use near open flame.
DRY & RECOAT TIMES
Dries to the touch in 30 minutes and can be recoated in 2
hours with latex or oil-based paints. For best results allow
the primer to cure overnight when applying solvent-based
topcoats.
CLEAN-UP
Wipe off tip before storing. Clean up wet paint with Xylol or
mineral spirits. Properly discard empty container. Do not
burn or place in home trash compactor.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object
into can valve opening.
(3 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels